424.0375
CC 3
NET ID 2h
I have not heard any voice transmissions yet.
I am getting a very strong signal in SW Calgary.
CC 3
NET ID 2h
I have not heard any voice transmissions yet.
I am getting a very strong signal in SW Calgary.
New DMR T3 in Calgary
- Thread starter maplebear
- Start date
Sounds like the AHS Hospital Network.
I thought it might be something like that.
It is a frequency that is used by the Children's Hospital but it was showing up as analog when I looked it up.
When I did a scan last Thursday it was not there, and last night's scan it was there.
Wonder if it is still being rolled out. Hope someone else in your area has some info.
Here in the Edmonton area quite a few DMR T3 AHS systems are up and running. Here TG 100 is usually wide area Security, 101 Local Security and 102 Grounds. Maintenance is above those but not any consistent talk group.
We have one for FMC/ ACH .
I am hoping it is one for the other hospitals and smaller centres.
I saw another license in the Richmond Road area is there a Health Centre there?
Richmond Road Diagnostic & Treatment Centre.
It was the old Children's Hospital.
Anyone know if there are still MPT1327 signals coming from RGH and PLC?
Last edited:
I picked up a new talk group 300 on FMC/ACH radio system. It sounded like security.
I actually heard someone say "Chumir Security to Maintenance" on 302 or 303, so I think the 300s are probably Chumir.
I put those into the scanner.
smason
Member
I work a few blocks from Chumir, so I'll have a listen.
smason
Member
Not getting much signal at all on my SDR at the office.
At home saw a few :
Group Call TG300 Ch=680
Group Call TG303 Ch=679
At home saw a few :
Group Call TG300 Ch=680
Group Call TG303 Ch=679
Can someone please recheck the FMC site.
I have these frequencies programed into the scanner. Which is different in what is listed on the database.
422.2125
422.4375
422.6625
424.5875
424.7875
Database has it as
422.2125
422.4375
422.6625
I have these frequencies programed into the scanner. Which is different in what is listed on the database.
422.2125
422.4375
422.6625
424.5875
424.7875
Database has it as
422.2125
422.4375
422.6625
I am still learning how to program this type of system into my uniden scanner.
would channel 680 be 424.2375?
Channel 648 would be 424.0375?
What is channel 679 be?
When I do site 2 Calgary Cancer Centre
451.1500 LCN is 4986
454.3875 LCN is 5504
When I enter the LCN the scanner only takes 3 numbers not 4.
The LCNs that worked for me on my SDS100 were half that of the ones that have been posted. Actually if I recall correctly, you divide by two and then subtract 1.
If your scanner only accepts 3 digits, maybe you can't program that site - I've only set up my SDS100 and SDS200 via Sentinel.
As for the question about site 1 and its 5 frequencies, notice that the last 2 frequencies are the same as site 4. I am thinking maybe they were added to site 1 in error. Run DSD+ and see if you get any 'hits' on frequencies 4 and 5 while listening to site 1.
If your scanner only accepts 3 digits, maybe you can't program that site - I've only set up my SDS100 and SDS200 via Sentinel.
As for the question about site 1 and its 5 frequencies, notice that the last 2 frequencies are the same as site 4. I am thinking maybe they were added to site 1 in error. Run DSD+ and see if you get any 'hits' on frequencies 4 and 5 while listening to site 1.
I haven't spent a lot of time in the city this week. I picked up site 4 (on an SDS100) when I was on the periphery the other day, but no voice. When I ran LCN finder, it only found one LCN out of two channels, and saved it as LCN 1, which I'm reasonably sure won't be right.
I may be in the city this coming week at some point, if the other participants in the thread don't have anything to contribute before then.
I may be in the city this coming week at some point, if the other participants in the thread don't have anything to contribute before then.
I am able to hear the voice traffic on sites #1 and # 3 from home. I am also picked a new talk group 107.
What device are you listening on and what are you using for LCNs?
