Dsd+ fastlane and cap+ noob question

[Asereje]

Hi folks, I am noob with the dsd + fastlane, I'm running a sdr v3 with sdrsharp and v cable and of course dsd+ fastlane. It decodes very well dmr in single channel, but now I found a cap + net with some sites and as you. Know each call changes the slot and site. The dsd+ detects the channels I see that but don't takes the call and doesn't change the frequency to follow that.
I have some questions :
1 I need more than a one sdr for cap+?
2 how I can configurate the dsd + fastlane for cap+?

Sorry but I'm noob and I didn't find any manual in the net.

Thanks any help will be appreciated

 

[TheButcher]

I use 2 v3 dongles for cap+ with more than 1 frequency. I am unsure if only 1 dongle could be used?

You need to add lines to the "DSDPlus.frequencies" file.


Also "DSDPlus.networks" & "DSDPlus.sites" files.

With some sites, the frequencies appear in DSD+, which is very handy!

 

[slicerwizard]

Cap+ is covered in the Notes.txt file. All trunk tracking in DSD+ uses two dongles.

 

[Asereje]

Thanks I'm looking the text files for that

 

[Asereje]

How to configure the two dongles in the dsd+?

 

[TheButcher]

Read the DSDPlus.txt and FMP.txt files. Instructions are contained within.

Also the Trunking.txt file.

 

[Asereje]

hi again, i add other rtl v3 dongle, and read all documents that you said me and also i watched videos on youtube, but i had the same error in fmp.

DSD+ 2.145
Program role is voice channel decoder; audio modes set to mono
Writing synthesized audio to per-call wav files
Source audio waveform window origin set to (400,210)
Source audio waveform window dimensions set to 100x200
Event log window origin set to (172,522)
Channel window origin set to (528,0)
Appending synthesized audio to file 'VC-DSDPlus.wav'
Current working directory is "C:\Users\2570b_6\Desktop\sdr sharp"

Assuming FMPA/FMP24 is signal source; auto polarity detect is disabled

Initiating TCP connection to 127.0.0.1:20002...
audio output device #1 = 'Altavoces (Dispositivo de High '
audio output device #2 = 'CABLE Input (VB-Audio Virtual C'

audio output device #2 (CABLE Input (VB-Audio Virtual C) initialized

P25 data loaded; 0 networks, 0 sites, 0 channels
26 frequency records loaded
13 radio records loaded
1 group record loaded
3 site records loaded
1 network record loaded
Fusion decoding enabled
D-STAR decoding enabled
NXDN4800 decoding enabled
NXDN9600 decoding enabled
DMR/MotoTRBO decoding enabled
P25 Phase 1 and Phase 2 decoding enabled
X2-TDMA decoding enabled
ProVoice decoding enabled
TCP connect error = 10061
[No connection could be made because the target machine actively refused it]


Initiating TCP connection to 127.0.0.1:20002...
TCP connect error = 10061
[No connection could be made because the target machine actively refused it]

i get off my windows10 firewall, but i have the same error.

can somebody know what is wrong?

thx

 

[slicerwizard]

hi again, i add other rtl v3 dongle, and read all documents that you said me and also i watched videos on youtube, but i had the same error in fmp.

DSD+ 2.145
Program role is voice channel decoder; audio modes set to mono
Writing synthesized audio to per-call wav files
Source audio waveform window origin set to (400,210)
Source audio waveform window dimensions set to 100x200
Event log window origin set to (172,522)
Channel window origin set to (528,0)
Appending synthesized audio to file 'VC-DSDPlus.wav'
Current working directory is "C:\Users\2570b_6\Desktop\sdr sharp"

Assuming FMPA/FMP24 is signal source; auto polarity detect is disabled

Initiating TCP connection to 127.0.0.1:20002...
audio output device #1 = 'Altavoces (Dispositivo de High '
audio output device #2 = 'CABLE Input (VB-Audio Virtual C'

audio output device #2 (CABLE Input (VB-Audio Virtual C) initialized

You're sending DSD+ audio output to VB Cable?

P25 data loaded; 0 networks, 0 sites, 0 channels
26 frequency records loaded
13 radio records loaded
1 group record loaded
3 site records loaded
1 network record loaded
Fusion decoding enabled
D-STAR decoding enabled
NXDN4800 decoding enabled
NXDN9600 decoding enabled
DMR/MotoTRBO decoding enabled
P25 Phase 1 and Phase 2 decoding enabled
X2-TDMA decoding enabled
ProVoice decoding enabled
TCP connect error = 10061
[No connection could be made because the target machine actively refused it]


Initiating TCP connection to 127.0.0.1:20002...
TCP connect error = 10061
[No connection could be made because the target machine actively refused it]

You're using FMP when you should be using FMP24?

 

[dave3825]

DSD+ 2.145

Current working directory is "C:\Users\2570b_6\Desktop\sdr sharp"

Not sure how or why, but you do not need all the DSDPlus files in your sdrsharp folder.

 

[slicerwizard]

You do if you use that SDR# DSD+ plugin, because that's the folder that it runs DSD+ in. It's ridiculous.

 

[Ryangn]

You do if you use that SDR# DSD+ plugin, because that's the folder that it runs DSD+ in. It's ridiculous.

You do not have to have the DSD+ files in you SDR# folder. I think it's in the options of the DSD+ plugin that you tell it where to look for the DSD+ files to run DSD+ from. Sorry I am not sitting at my computer so I can't be any more specific and exact about it.

 

[DRL-XM43]

It is not necessary or wise to use sdr# (no point) the DSD+ plugin does not support fastlane versions anyway. You definately will not get P25 II.

You need to use FMP24 feeding DSD+ by using TCP connection

You should not be using a VB cable.

You should have a DSD+ folder with all the files supplied in it.

Now you can begin to set up to decode as intended.

 

[slicerwizard]

You do not have to have the DSD+ files in you SDR# folder. I think it's in the options of the DSD+ plugin that you tell it where to look for the DSD+ files to run DSD+ from.

No, that only tells the plugin where DSDPlus.exe is. It still runs DSD+ in the SDR# folder, which means the SDR# folder is where DSD+ looks for its data files (.networks, .sites, .groups, .radios, etc.) and that's where DSD+ writes its event log, .bin file, yadda yadda...

Someone who uses the plugin on a regular basis should be able to confirm this.

 

[Ryangn]

No, that only tells the plugin where DSDPlus.exe is. It still runs DSD+ in the SDR# folder, which means the SDR# folder is where DSD+ looks for its data files (.networks, .sites, .groups, .radios, etc.) and that's where DSD+ writes its event log, .bin file, yadda yadda...

Someone who uses the plugin on a regular basis should be able to confirm this.

I can't confirm that one way or the other. I don't use DSD+ on a regular basis and when I do it's just to park it on a single freq for the neighboring sheriffs dept. Since that sheriffs dept only has one freq and only one or two deputies on at a time I don't pay any attention to data files. I learned something new.

 

[slicerwizard]

Just check for any DSD+ files in the SDR# folder...

 

[Asereje]

Hi folks I am able to make tcp connection in both places. But I have a another problem because in cc control window I see there the waves but in vc dsd window not and but it seems that its no working.
In another hand in dsd + events window only appears p25 decode and I need dmr cap+ decode, how I can change it?
Thx