Search results

  1. B

    MTR3000 with RAS enable

    Actually that was on the radios I guess, not the repeater. I see no settings on the actual repeater side within the CPS to enable this feature.
  2. B

    MTR3000 with RAS enable

    I have a MTR3000 repeater and under the options it lists RAS as included, Free, however when I got to the security section it shows disabled and grayed out. Any idea how to enable RAS on this repeater? Thank you
  3. B

    MTR3000 VSWR error

    I did try reversing. I took the setup out to the site and hooked up everything with the duplexer and get the error. If I unhook from the duplexer and hook the antenna directly to the transmit side on the repeater, there is no error. I think it is the duplexer, so will need to confirm it is...
  4. B

    MTR3000 VSWR error

    With an antenna hooked direct to the receiver and transmit side of the repeater, I get no error. Looks like it is probably a duplexer issue. Thanks for the replies.
  5. B

    MTR3000 VSWR error

    This is a new setup
  6. B

    MTR3000 VSWR error

    Yes, the duplexer is supposed to be tuned to my frequencies, but I have no way of checking it.
  7. B

    MTR3000 VSWR error

    I also unhooked the duplexer and left the receive antenna hooked up, but put a dummy load on the transmit side of the repeater and no error. With an antenna on the transmit side I get an error. Thanks
  8. B

    MTR3000 VSWR error

    Yes, I have two dummy loads. So I unhooked the duplexer and tried dummy loads direct to the repeater with no error. Hooked the duplexer up and hooked dummy load to antenna port and got the error.
  9. B

    MTR3000 VSWR error

    No I did not, it is at a remote site just in a test bench environment. I did change out the cabling and tested both ways between the repeater and duplexer, which did not make a difference.
  10. B

    MTR3000 VSWR error

    I appreciate the replies. So I did some testing, unhooked the duplexer and hooked up a dummy load to each side of the repeater and no error. The minute I hooked up the duplexer I got the error. I am assuming at this point it is the duplexer and if that is the case, is is just a bad duplexer...
  11. B

    MTR3000 VSWR error

    My MTR3000 repeater is giving me a VSWR error. It operates fine and repeats the signal, but immediately after operation the red LED come on. I have RDAC and checked condition, says VSWR minor alarm. What could be causing this? Thanks
  12. B

    Motorola MTR3000 entitlement code issue

    Does anyone has experience with programming a Motorola MTR2000 or 3000 repeater? I bought dynamic mixed mode for it, but I think I got the wrong part number as it is for the wrong region and I cannot get it to load on my repeater. I successfully register the EID (entitlement code) using the CPS...
  13. B

    Outdoor repeater installation enclosure

    Not sure if this is the right forum or not to ask this. I have an opportunity to install a repeater antenna on a tall tower assembly. The issue is there is not climate controlled indoor structure near it. Wondering the possibility of installing the repeater in a weatherproof enclosure. I am...
  14. B

    MTR3000 flashing amber status light

    Disregard that last question, I would need another repeater for that.
  15. B

    MTR3000 flashing amber status light

    Thanks, I figured it out. I did not have the admit criteria set to color code free. One question though, is it possible to set this repeater to accept two different digital channels with two different sets of frequencies? Set one to slot 1 and the other to slot 2?
  16. B

    MTR3000 flashing amber status light

    Well I have another issue, I cannot get the repeater to operate in digital mode. It works fine in analog. I have confirmed that the color code is correct, frequencies are correct as it does work in analog. I see that RAS says disabled and grayed out, so not even sure where I could enable...
  17. B

    Motorola XPR7550E not programming

    I was able to successfully recover the device and it did go back to the default codeplug, however when I tried to put my custom one back in it did the same thing. Anyway have any other ideas? Thanks
  18. B

    MTR3000 flashing amber status light

    I put a dummy load on it and no error now, looks like that worked. Thanks for the help
  19. B

    Motorola XPR7550E not programming

    I just got a couple of XPR7550E VHF radios. I was able to program one with no issues, but the second one does not take the program. I get no errors from the CPS and says write was succesful, but when you go to the radio nothing comes up and it just says Searching Multi Group. If I read from...
  20. B

    MTR3000 flashing amber status light

    No, nothing hooked up just on a bench right now
Top