Search results

Thank you..i thought I'd take a shot in trying to wire up the old to new.

Hello- Let me start by saying I have never dealt with Kenwood radios. I have a FD who wants the old Motorola desk mics (used with CDM series VHF radios) to work with the new P25 Phase 2 trunking Kenwood. I get the new radio to key up, but no audio. I took the mic apart and it has quite a bit of...

I have a yagi like the one you specified, and it works pretty good. I tried an omni with low satisfaction for my purpose. 35 miles is a stretch unless you have flat land between you, or you are up on a mountain. What system are you looking to receive? I have a SDS200 in Newberry SC, and I have a...

Good day- I would like to get some better reception on my Sangean SG-114 HD FM radio. It only comes with a wire antenna with no external connection for an antenna. I added a BNC connector and wired the center conductor to the same output of the wire antenna that came with it. However, I don't...

Hello- Pardon this post if it has been discussed already. I am looking to set up a feed at my in-law's home several states away from me. I run a couple remote scanners w/ PCs at friends houses in reasonable driving distance, but I am looking to set up something basic at my in-laws without using...

Is this system still hard to receive? When this thread started, they were silent for me as well. Then, when i posted above, I could hear them. I recently upgraded scanners, and now I can't hear them again. I was wondering if I programmed it wrong, or it's just a coincidence they went silent...

Just heard Ludlow PD loud and clear. I, too, haven't been hearing them at all in the last week or so, but they are back up now.

Thanks for the links! I'll check it out

Forgive me if I seem ungrateful, which is certainly not the case. I value all of the info everyone has given. My major setback right now, is I just can't start to test any time I wish, because of poor location and currently no outside antenna. I did a google search for Con+ and Cap+ and I...

Well, I don't know what Con+ and Cap+ is, so that's a disadvantage for what I'm looking for LOL

Thanks, This does help. I thought the VR cable was before the DSD...I have both VB & audio cable.. My trouble is finding a DMR freq. .. where I am testing this, I have VERY poor reception, in a valley between 2 granite mountains essentially.. so I have to trek up to a higher location to try this...

OK.. then how does it work?? I DON'T want to listen to static, but I thought I would hear something to make sure audio is running through the hardware, software, soundcard,etc. I am new to SDR, and all other times I monitor , I hear traffic/ static. So, I was expecting to hear radio traffic...

OK, Perhaps I didn't understand the purpose of DMR & DSD... If it''s working properly, it will NOT let through audio, unless an appropriate signal is received and decoded? I was expecting it to act as an open squelch scanner where I would hear static or something (Which is why I had the freq...

Regardless of any frequency I'm still not getting audio. The location I was testing this, I have no digital signals in any band. You mentioned a filter, could this be an issue? I see it now you mention it- never noticed it before, so many settings and all

Sorry if this was discussed before, but I can't seem to get SDR# to play back audio using the DSD interface. I am trying to set up DMR decoding. I've been fooling with it for a few hours at least. Let me start by saying I watched, and followed How To Setup SDR # Sharp To Decode DMR Digitial...

Anyone have problems (with Version 12.3) of the program locking up when recordings are attempted to be played back?

Thanks for all of your recent updates. I have all feeds running smoothly. One question, is there a way (perhaps in a future update) to separate the audio on a feed, i.e. "left/right/stereo"? I have a few stereo feeds I listen to that I only like to hear one side of the feed (i.e. police on...

Re: Update I still can't get more then 8 feeds to run at once...

Hampshire County codes Not sure if some of these numbers are also used for the police agencies in Hampshire County, but here are the Fire Dept ID numbers.. some departments still use them: Amherst - 51 Belchertown - 52 Chesterfield - 53 Cummington - 54 Easthampton - 55 Goshen - 56 Granby...

I too share the problem. I can run 6 instances of ScannerLive connecting to me to about 55 feeds with no problems.., and 2 Proscans running as well .. but even after shutting them all off, I max out at connecting to only 7 or 8 feeds with Radiolog Everything else seems to work well, I enjoy the...