Search results

I appreciate the replies. I guess everything I have read about NVIS is calling for an antenna that looks more like an inverted V, to get better antenna pattern more vertical. Based on what I am hearing, a basic dipole or endfed that is horizontal closer to the ground will work just as well, is...

I guess it was a more general question if anyone has had experience, successes with NVIS under 100 miles and what they used. We have tried using a Buddipole setup for NVIS, early evening (still daylight hours, towards dusk), power level one radio was at 10 watts and other station was at 100...

I am trying to setup communication between two sites about 80 miles away from each other. We have been experimenting with NVIS, 40 meter but have not been getting good results. I am wondering if anyone else has experience with this type of communication under 100 miles on HF? I think our...

`Apparently my scan was on. Is there a way to default it so the scan does not automatically come up?

I have my XTS2500's programmed now with a couple of different zones and channels. However, you can hear across all channels now. If I am on channel 1, all the other radios that might be on a different channel can still here me. I want it so you can not cross over different channels, if you...

I appreciate the input on this. I just went ahead and created a simple codeplug for them. I had CPS 16 828, but my firmware was older, so I must have at some point needed to upgrade to newer firmware when they still had it available. I have not looked at these radios for probably four years...

Yeah, I tried that also, same error, no matching packages exist. I am just deleting all the contacts, channels etc. manually. Thanks

Yes, I installed the firmware pacakges and I am going to sell these radios so want to make sure they are updated and cleaned up. I need to reset to factory settings.

I have the CPS 16.0 build 828 installed now and also installed the Release R02.10.10. However when I go to the CPS and try to update it gives me a message that no matching packages exist.

Did you mean the MOTOTRBO NA Professional Devices Release R02.10.10, because that has the XPR7000e series radio in it. The Commercial Device Release only lists the CP200 and SL300. Thanks

The oldest version I can still download from Motorola is 2.110.120.0. So not sure where I get 2.09. Thanks

I have some XPR7350E's that have not been updated for a few years and still under the older CPS and firmware. I am not able to update firmware with the newer CPS 2.0. What I have seen is I need to update to the latest firmware prior to the switch to CPS 2.0, but you are not able to find that...

Appreciate the replies. I found the issue, I had dual capacity direct model enabled on those channels on the Motorolas. Turn it off and they communicate fine.

Has anyone had any experience with XPR7000 series radios communicating directly with TYT DMR radios, such as MD-UV390? I have both radios in my system and I am not able to get the two to talk to each other. I confirmed the contact list is the same with the same ID's and privacy is off on both...

Any idea where I can disable that service reminder at? I don't see any options for that in the CPS. Thanks

I have some XPR radios that I just updated the firmware and one of them keeps announcing "Service Recommended" Anyone have this before? Thanks

I am not able to access MyView under the software section, entitlements. It just says loading forever then says an error occurred. Has anyone else had this issue? Thanks

I have a MTR3000 repeater that I an unable to disable, remove the RAS key it forces me to put a value in there and we want to turn RAS off. Any ideas? Thank you

I have been working with this CPS a bit, trying to learn it. When trying to update the firmware it is asking for a system key / flash key. Is that just some sort of software that has to go in or is it a physical connection? I guess these radios are a lot different in that aspect from the...

These are VHF radios for commercial bands. Great, thanks I will contact them.