rbm
Member
A recent power outage prompted me to start mapping out the new NYSEG trunking systems. I'd like some input from other areas as well. (Talk groups, CC's, etc.)
Below, I've listed the P25 Control Channels I can receive from my location north of Binghamton using an outside antenna and low noise pre-amps. So, some of them are quite distant from me.
They can be a starting point for other areas in the state. I'll also post a few of my 'CC Only' programming files, in usd format, for Uniden scanners.
152.0825 SID:0269H-0109
152.0975 SID:0269H-0105 (Copied in Owego so may cover Chemung Co. also)
152.1425 SID:0269H-0107
152.2175 SID:0269H-0119
152.5175 SID:0269H-0103
152.5325 SID:0269H-0108
152.7425 SID:0269H-0118
152.7575 SID:0269H-0115
153.2150 SID:0269H-0112
153.2600 SID:0269H-0101
The Talk Groups I have so far:
Vestal Electric 121
Vestal Gas 122
Vestal Meter 123
Elmira Electric 141
Elmira Gas 142
Elmira Meter 143
Ithaca Electric 171
Ithaca Gas 172
Ithaca Meter 173
Unknown 131
Unknown 191
Unknown 193
NOTE: In all of my Uniden programming files, the System Quick Key is the first two digits of the file name. (ie. SQK = 30 in the file below.)
In the ZIP file attached, the "30 NYSEG CC.usd" file has most of the known and potential CC frequencies in it. It defaults to "ID Search" mode. So, if you only activate that system, and then hit HOLD. You can open your squelch and turn the dial through all of the frequencies. The squelch noise will go away on an active CC and the SYSID will be displayed.
There also is a system file for each of the sites I've identified. (ie. "99 NYSEG 0112"), The SITE is the last four digits (0112).
Rich
Below, I've listed the P25 Control Channels I can receive from my location north of Binghamton using an outside antenna and low noise pre-amps. So, some of them are quite distant from me.
They can be a starting point for other areas in the state. I'll also post a few of my 'CC Only' programming files, in usd format, for Uniden scanners.
152.0825 SID:0269H-0109
152.0975 SID:0269H-0105 (Copied in Owego so may cover Chemung Co. also)
152.1425 SID:0269H-0107
152.2175 SID:0269H-0119
152.5175 SID:0269H-0103
152.5325 SID:0269H-0108
152.7425 SID:0269H-0118
152.7575 SID:0269H-0115
153.2150 SID:0269H-0112
153.2600 SID:0269H-0101
The Talk Groups I have so far:
Vestal Electric 121
Vestal Gas 122
Vestal Meter 123
Elmira Electric 141
Elmira Gas 142
Elmira Meter 143
Ithaca Electric 171
Ithaca Gas 172
Ithaca Meter 173
Unknown 131
Unknown 191
Unknown 193
NOTE: In all of my Uniden programming files, the System Quick Key is the first two digits of the file name. (ie. SQK = 30 in the file below.)
In the ZIP file attached, the "30 NYSEG CC.usd" file has most of the known and potential CC frequencies in it. It defaults to "ID Search" mode. So, if you only activate that system, and then hit HOLD. You can open your squelch and turn the dial through all of the frequencies. The squelch noise will go away on an active CC and the SYSID will be displayed.
There also is a system file for each of the sites I've identified. (ie. "99 NYSEG 0112"), The SITE is the last four digits (0112).
Rich
Last edited: