- Joined
- Apr 25, 2011
- Messages
- 1,401
Do you ever see "(TG PRI)" at the end of the line in the talk group log?Hello all
I am working with my p25rx and cant seem to get the priority's working attached is my talk groups file
No sir never haveDo you ever see "(TG PRI)" at the end of the line in the talk group log?
No sir never have
Very reluctantly selling my unit to generate some cash flow after major surgery Listed in RR Classifieds........
I have tried all the setting from 100 ms to 5 sec and nothing showing up with Tg PriBtt have it at 250ms I will increase it and let you know thanks
What version are you using? The first version that output the (TG PRI) to the talk group log was version: 2020-11-14_1212I have tried all the setting from 100 ms to 5 sec and nothing showing up with Tg Pri
11-26-1529What version are you using? The first version that output the (TG PRI) to the talk group log was version: 2020-11-14_1212
I should have noticed the software date on the image you posted earlier. I'm not sure why it is not working for you. I'm testing here with a very similar configuration to yours. It appears to be working good. (default 2 second talk group timeout). I will continue to search for a possible solution.11-26-1529
I haven’t had it work since I had it several versions back that why I was asking about the command to show the talk groups that was assigned priority I have also tried just leaving it on one control channel to see if that made a difference I have was also done factory reset with no luck
Wonder if I should factory reset and re enter the talk groups from scratch cause I am using my talk group from my original buildI should have noticed the software date on the image you posted earlier. I'm not sure why it is not working for you. I'm testing here with a very similar configuration to yours. It appears to be working good. (default 2 second talk group timeout). I will continue to search for a possible solution.
I don't think that will help. I found a case in the firmware where the (TG PRI) string was not being added to the log when it should be. Try version 2020-11-29_0307.Wonder if I should factory reset and re enter the talk groups from scratch cause I am using my talk group from my original build
Good Moring SirI don't think that will help. I found a case in the firmware where the (TG PRI) string was not being added to the log when it should be. Try version 2020-11-29_0307.
Hope to have a few ready this afternoon.When will the P25RX units be back in stock?
The (TG PRI) will only show up if the current talk group being held (in this case for the 3 second period) is interrupted by a higher priority talk group within the 3 second period. The interrupt only happens at the time of the channel grant. In other words, the receiver has to return to the control channel due to an "end of call" message or timeout on the voice channel before the channel grant will be processed.Good Moring Sir
I have done the firmware update it is now showing the (TG PRI) but not ever time the talk group is shown I have to talk group time out set to 3 sec. Also it not interrupting the talk it is currently on for the one that is set for Priority
Ok thanks and thanks again for your hard workHope to have a few ready this afternoon.
The (TG PRI) will only show up if the current talk group being held (in this case for the 3 second period) is interrupted by a higher priority talk group within the 3 second period. The interrupt only happens at the time of the channel grant. In other words, the receiver has to return to the control channel due to an "end of call" message or timeout on the voice channel before the channel grant will be processed.
I have mine working on a UHF DMR Connect Plus system. It uses frequencies between 450 and 472 MHz. So it should work.I have a DMR system in the 450 MHz range in my area. It is my understanding From earlier posts that this unit will not receive this system. Am I correct with that statement?