radio shack pro 106

[VE3JSO]

huh i always thought it was 380 lo chan then 759 for the hi chan guess you learn something new every day

 

[Forts]

Apparently it's not that fussy about it. Those settings I listed last night were from my Toronto V-Scanner file (I'm in Toronto currently). I just checked my 'Home' V-Scanner and with that one I'm using:

Low: 380 Hi: 759 for all of them. Offsets are 380, 579 and 632. I don't think the lo/hi value is overly critical as long as the system channel values fall within that range, and you have the proper offsets selected.

Gardenlily46: I have sent your file back to you with a few changes. Give it a twirl and see how it goes...

 

[troubleshooter1]

I recently took a drive over to the area covered by 37 VANKLK (Vankleek Hill tower) in Zone 2. I never saw 152.000 come up in over two hours, but I knew it was active from MTrunk32. Sure enough, my custom tables were wrong. After correcting them, I went again this past Wednesday, and now 152.000 is part of the mix like all the other voice frequencies. The same should apply for 40MOWT (Mowat tower) in Zone 1, but I'm not ready to travel to Toronto just to try it! Perhaps someone in the area could verify that it works there as well.

With reference to the Custom Frequency Tables at Bell Fleetnet - Ontario Provincial Government Zone 2 Trunking System, Southeast Zone, Ontario - Scanner Frequencies

Currently in my Pro-106 and my GRE PSR-600:

Table 01:
Lo Chan: 380
Hi Chan: 578
Offset: 380
Base: 141.015000
Step: 15.000

Table 02:
Lo Chan: 579
Hi Chan: 631
Offset: 579
Base: 151.730000
Step: 15.000

Table 03:
Lo Chan: 632
Hi Chan: 759
Offset: 632
Base: 154.320000
Step: 15.000

A Motorola Type II system can't have more than 760 channels; channels 0 - 379 are repeater inputs, and channels 380 - 759 are repeater outputs. Any channel number higher than 759 is not valid.

 

[gardenlily46]

ref radio shack 106 pro

i have put the freqs in the scanner and the table numbers are wrong so i enter them myself and i keep getting an error that sayes heap error 222d1f : 2234 what does this mean and why am i getting this and im using win500 program 30 day free trail hope someone can figure out why im getting this thanks indavance gardenlily 46

 

[pathalogical]

The psr 500 is the same radio as the 106, PSR-500/600 Heap Errors - Powered By Kayako SupportSuite

 

[mikewazowski]

Gardenlily, I've merged your new thread into the existing thread.

It's much easier for people to help when they can see what the steps were in the other posts that led to your problem.

Please don't create a new thread for the same problem. Find your existing thread and continue with it.

Thanks.

 

[gardenlily46]

it doesnt matter what button i push on the scanner the error comes up so that meanes im going to have to put it back to factory mode will it get rid of the error for good it has only happened since i used the win500 i used the psedit500 and never came up at all gardenlily46

 

[VE3JSO]

On win 500 look for any talk group that is not part of a tsys if you find one correct it or delete it to see if that helps

 

[gardenlily46]

re pro 106

i tryed everything to get the scanner to work but the error still came up so i put it back to factory and programed everything again and uploaded it to the scanner and i didnt get the error and it is working great so far thanks again for your help with the scanner gardenlily46