DeoVindice
P25 Underground
Looking at the mic jack on several Vertex mobiles, it looks to be the same as on most Kenwood mobiles. Does anyone know if this is the case, and if so, whether or not the pinouts are also the same?
-
To anyone looking to acquire commercial radio programming software:
Please do not make requests for copies of radio programming software which is sold (or was sold) by the manufacturer for any monetary value. All requests will be deleted and a forum infraction issued. Making a request such as this is attempting to engage in software piracy and this forum cannot be involved or associated with this activity. The same goes for any private transaction via Private Message. Even if you attempt to engage in this activity in PM's we will still enforce the forum rules. Your PM's are not private and the administration has the right to read them if there's a hint to criminal activity.
If you are having trouble legally obtaining software please state so. We do not want any hurt feelings when your vague post is mistaken for a free request. It is YOUR responsibility to properly word your request.
To obtain Motorola software see the Sticky in the Motorola forum.
The various other vendors often permit their dealers to sell the software online (i.e., Kenwood). Please use Google or some other search engine to find a dealer that sells the software. Typically each series or individual radio requires its own software package. Often the Kenwood software is less than $100 so don't be a cheapskate; just purchase it.
For M/A Com/Harris/GE, etc: there are two software packages that program all current and past radios. One package is for conventional programming and the other for trunked programming. The trunked package is in upwards of $2,500. The conventional package is more reasonable though is still several hundred dollars. The benefit is you do not need multiple versions for each radio (unlike Motorola).
This is a large and very visible forum. We cannot jeopardize the ability to provide the RadioReference services by allowing this activity to occur. Please respect this.
Vertex/Kenwood Mobile Mic Compatibility?
- Thread starter DeoVindice
- Start date
- Status
mmckenna
I ♥ Ø
I doubt it.
While they often use RJ-45 connectors, the pinout is not standardized between manufacturers. There is usually some low voltage, data, PTT and various signaling pins, getting those wrong can create issues. Probably not destroy anything, though.
While they often use RJ-45 connectors, the pinout is not standardized between manufacturers. There is usually some low voltage, data, PTT and various signaling pins, getting those wrong can create issues. Probably not destroy anything, though.
Our school buses use a mix of Kenwood and Vertex mobiles. Recently, one showed up at the shop saying no one could hear them (Kenwood installed). They had broken their microphone and replaced it with a Vertex unit they found somewhere. It didn't work at all but also didn't break anything.
DeoVindice
P25 Underground
Understood, thanks for the advice.
- Joined
- Nov 22, 2015
- Messages
- 7
Not wanting to hijack the thread but continuing conversation about this I am in the same situation as I have a Kenwood TM-733 and a Vertex Desk Mic and wouldn't mind tinkering attempting to make an adapter to change the pinout for compatibility if anyone has information or thinks this may work?
kayn1n32008
ØÆSØ
Find the pinouts and schematics for each, and see. You will likely need to put a new plug on the Vertex with the correct wires in the correct pins.
It was bought out by motorola but vertex are not pinned like motorola rj45.
- Joined
- Nov 22, 2015
- Messages
- 7
Wouldn't be a problem to do that as I have the things to make a new end on it but I have a Kenwood KMC-9c on the way and will test and also research the pinouts and if I can figure out the correct wiring I will make a perf board showing which pins move where and post pics if I can get it to work.
That's good engineering on both company's part. It's always good practice to make any user-accessible connection as fail-safe as possible. On mic connectors, as current levels needed in the mic are extremely low, current limiting is often used. That type of interconnection could still result in a stuck transmitter, though (depending on the specific pinouts of the mic and the radio in question)
- Status
Similar threads
