VHF Phase 2 NAS

[joespca1]

Hello wondering if anyone has experience programming phase 2 vhf nas? I have done phase 1, just wondering if phase 2 on vhf is any different?

 

[KevinC]

Hello wondering if anyone has experience programming phase 2 vhf nas? I have done phase 1, just wondering if phase 2 on vhf is any different?

No different at all.

 

[joespca1]

No different at all.

Are you able to assist me and see if I'm doing something wrong ?

 

[K2NEC]

What relevance does VHF have to this?

 

[joespca1]

What relevance does VHF have to this?

I didn't know if programming uhf phase 2 was different then vhf. That's why I was asking

 

[exkalibur]

The only "difference" is make sure you have Phase 2 enabled in your system settings.

 

[joespca1]

I'll try that

 

[K2NEC]

I didn't know if programming uhf phase 2 was different then vhf. That's why I was asking

Band has nothing to do with it, programming is exactly the same across the board. All that's different is your control channels

Honestly I'm waiting for the NAS warriors to show up in this thread..

 

[Asunakiyori]

Band has nothing to do with it, programming is exactly the same across the board. All that's different is your control channels

Honestly I'm waiting for the NAS warriors to show up in this thread..

and the P25 tables...

 

[joespca1]

Band has nothing to do with it, programming is exactly the same across the board. All that's different is your control channels

Honestly I'm waiting for the NAS warriors to show up in this thread..

What do you mean control channels are different ? As different per system ? I would assume that's what it is.

I can do uhf nas perfect never attempted vhf. But if it's the same as uhf I'm site I'll get it done

 

[KevinC]

What do you mean control channels are different ? As different per system ? I would assume that's what it is.

I can do uhf nas perfect never attempted vhf. But if it's the same as uhf I'm site I'll get it done

As long as you have all the system info (system ID, WACN, Bandplan and control channels) you have everything you need.

 

[joespca1]

Perfect I'll try it out thanks

 

[exkalibur]

I believe newer firmware uses the iDEN data that is sent OTA but I'd still make sure everything matches.

 

[joespca1]

Is my flashcode phase 2?

Codeplug Feature Set
H38-SMARTZONE Systems Operation Yes
Q806-ASTRO Digital Operation Yes
Q173-SMARTZONE OMNILINK Multizone Operation
Q361-ASTRO 25 9600 Baud Trunking Systems Operation
G996-Over the Air Provisioning No
Q498-OTAR with Multikey Yes
Q52-Federal Government Front Panel Programming Enhancement
QA00569-7/800 MHz Primary Band Yes
QA00574-VHF Secondary Band Yes
QA00579-Enable Dual Band Operation Yes
QA00583-Bluetooth No QA01833-Extreme Noise Reduction Yes
QA00631-DVRS PSU Activation No
QA00782-GPS Activation No Q947-Packet Data Interface No
Q387-Conventional Voting Scan No No Yes Yes
QA09000-Tone Signaling No
QA00580-TDMA Operation Yes
QA00577-Front Display and Full Keypad
QA01749-Legacy SW System Key Enable Yes No

 

[GTR8000]

Well I mean, it does have QA00580, so...

Your ASTRO 25 Channel ID table is likely not setup correctly for TDMA operation. Especially important for ASTRO 25 VHF systems like Chautauqua County's.

 

[joespca1]

Well I mean, it does have QA00580, so...

Your ASTRO 25 Channel ID table is likely not setup correctly for TDMA operation. Especially important for ASTRO 25 VHF systems like Chautauqua County's.

I sent you a PM with the configuration

 

[joespca1]

I sent you a PM with the configuration

Never mind i can't PM you