I have a top group of 37038 programmed into my scanner for Muskingum County but not receiving anything for Zanesville Police dispatch. I can hear them broadcast on other apps. Other departments in that group are working. (Sheriff, fire, etc)
Zanesville police
- Thread starter Smash714
- Start date
Working same as always - just ran back recordings from the last hour. Not very active FWIW.
What site are you using? Either So zanesville Or Dresden should get it.
37018 is correct
On the scanner - go to analyze and see how your signal is.
best manual to use for anything. Easier to Read BCD436/536HP Digital Scanner Manual
On the scanner - go to analyze and see how your signal is.
best manual to use for anything. Easier to Read BCD436/536HP Digital Scanner Manual
Export your list as an hpe. rename it to whatever.txt (can not attach a hpe) and attach and I'll look at it.
In Sentinel - file - export hpe.
In Sentinel - file - export hpe.
Not sure how many posts you need before you can PM and attach files.
I'll load into my sds100 and try it, only obvious issue - add quick keys to sites and usually only use 1 or 2 sites.
Each site takes 2 seconds to scan so will slow down the scanner.
Each site takes 2 seconds to scan so will slow down the scanner.
tvengr
Well Known Member
37018 is listed as Community Ambulance in the database.
so far - this is what I see.
I'd add quick keys for Sites. That is too many to cycle through without missing stuff.
For OSP add
Since they use this consolidated dispatch, often POST 60 will use this.
I’d just add all these.
That VHF for Med Helicopters is also not used.
I’d add quick keys for HAM and FRS – maybe some others, but that’s up to you.
I'd also add quick keys for Sites.
I'd add quick keys for Sites. That is too many to cycle through without missing stuff.
For OSP add
| Post 79 | - | 51760 |
I’d just add all these.
| District Radio Technicians | - | 51753 |
| Post 07 St Clairsville | Avoid | 51752 |
| Post 30 Cambridge | - | 51530 |
| Post 30 (Cambridge) Tac | - | 51615 |
| Post 41 (Steubenville) Dis | - | 51541 |
| Post 41 (Steubenville) Tac | - | 51620 |
| Post 60 | - | 51560 |
| Post 60 Tac | - | 51632 |
| Post 7 (St Clairsville) Tac | - | 51598 |
| Post 79 | - | 51760 |
| Post 79 Tac | - | 51643 |
| Post 84 | - | 51584 |
| OSP F3 | - | 51666 |
The Muskingum Co VHF High Fire and LEO – don’t think any of those are used anymore except main FD dispatch and extenders for Musk SO 154.65 For Fire -155.055 is all you need, unless one of the others (repeaters) works better. |
I’d add quick keys for HAM and FRS – maybe some others, but that’s up to you.
I'd also add quick keys for Sites.
No - maybe just the scan time or amount of VHF channels. Takes a fairly long cycle time.
I have 3 scanners - 1 for OSP, 1 mainly for SO and ZPD, and one just for AMB. There is some low-priority stuff scattered through them. I have another that is just Parr and ZZV airport, but it's usually off.
All that and still miss stuff. Have another 5 or 6 I can haul in and use in case something is going on.
Not really
Run analyze - see what sites you get. What antenna? That one that comes with it is OK for a few miles. add in a few Ohio Hills and some miles, and not so good.
Where (roughly) are you located?
I'm North off Maple. I need a small outside ant. to consistently get Dresden and So Zanesville. I can get a few other sites, yet not 100% - true for all the radios I own.
I've been using a 536 for 5 years, maybe more - needed to be repaired once, and now the dongle seems to not work, but overall - pretty foolproof.
PD has lot of no air time - my last transmission was over an hour ago. I log it all with Proscan. Most dispatches are by MDT.
