BCD325P2/BCD996P2: DMR upgrade

Status
Not open for further replies.

firetext911

Member
Premium Subscriber
Joined
Oct 10, 2012
Messages
23
Location
Trumann, AR
I have purchased the upgrade and I can not get the the audio to work.
The WX channel is working, I have downloaded from RRDB.
It is set and correct CC and TGID, everything appears correct but it will not pickup audio
 

firetext911

Member
Premium Subscriber
Joined
Oct 10, 2012
Messages
23
Location
Trumann, AR
I am not getting any audio output from the frequency.
I have it pull data from RRDB.
Sent to the scanner.
I did purchase the upgrade and its set in the menu.
When they talk on the radio, the scanner does not pick itup.
Am I missing something?
The WX channel works and picks up.
Other devices in the same room picks up.
any suggestions?
 
Last edited:

firetext911

Member
Premium Subscriber
Joined
Oct 10, 2012
Messages
23
Location
Trumann, AR
For me downloading a DMR system from R/R doesn’t work as far as audio, but using that information and loading it by hand it does work, now that’s on my SDS. If I down then load that same information on to my TRX scanner it works just fine as downloaded! Good luck
I am using Uniden BCD996P2.
I had it working at one point but it would have voice for about 5 seconds then go digital.
I cleared settings factory reset scanner, and retried it. But now its not picking up anything.
 

ProScan

Software Provider
Premium Subscriber
Joined
Jul 2, 2006
Messages
7,837
Location
Ontario, Calif.
I have purchased the upgrade and I can not get the the audio to work.
The WX channel is working, I have downloaded from RRDB.
It is set and correct CC and TGID, everything appears correct but it will not pickup audio
What software are you using?
Can you provide a link to the RRDB system.
 

KevinC

The big K
Super Moderator
Joined
Jan 7, 2001
Messages
12,519
Location
1 point
OP's location shows as Trumann, AR. I see in the RR database the PD is encrypted NXDN.
 

firetext911

Member
Premium Subscriber
Joined
Oct 10, 2012
Messages
23
Location
Trumann, AR
Finally got audio but only after about 3 seconds. I am missing the whole conversation except for the first 3 seconds or the last three seconds.
 

n1chu

Member
Premium Subscriber
Joined
Oct 18, 2002
Messages
2,913
Location
Farmington, Connecticut
What software are you using?
Can you provide a link to the RRDB system.
CLMRN stands for Connecticut Land Mobile Radio Network. It’s a statewide trunked simulcast system the state police, DMV, DEEP, DOT to mention a few, along certain towns and cities. Ham radio also has their ARES system on the CLMRN, using it in DMR mode.
 

KevinC

The big K
Super Moderator
Joined
Jan 7, 2001
Messages
12,519
Location
1 point
CLMRN stands for Connecticut Land Mobile Radio Network. It’s a statewide trunked simulcast system the state police, DMV, DEEP, DOT to mention a few, along certain towns and cities. Ham radio also has their ARES system on the CLMRN, using it in DMR mode.
Thanks???
 

ProScan

Software Provider
Premium Subscriber
Joined
Jul 2, 2006
Messages
7,837
Location
Ontario, Calif.
I am using ProScan BCD996P2.
Is this the link you mean,
This is the system. Correct?

Finally got audio but only after about 3 seconds. I am missing the whole conversation except for the first 3 seconds or the last three seconds.
What did you do to get the audio?
Is it doing that constantly on all the channels or sites you're monitoring?
 
Status
Not open for further replies.
Top