CURRENTLY I AM PROGRAMMING A XTS 1500 VHF WITH FREQWENCY OF 152.42750 WITH A DPL OF 703 AND A TRANSMIT OF 157.68570 DPL 703 IS THE SAME AS RX, I CURRENTLY CAN TRANSMIT BUT NOT RECIEVE ALL I GET IS A BLINKING LIGHT ON TOP. IM USING AND UNMUTE STD MUTE WITH A SQUELCH FINE TUNE OF 6 NON ASTRO. BUT IF I USE CSQ I GET RX NO PROBLEM BUT A TON OF BLEED THROUGH FROM A TAXI COMPANY . CAN SOMEONE HELP ME ON THIS IM SO LOST ON WHAT I DID ANY HELP WOULD BE GREAT THANK YOU .
-
To anyone looking to acquire commercial radio programming software:
Please do not make requests for copies of radio programming software which is sold (or was sold) by the manufacturer for any monetary value. All requests will be deleted and a forum infraction issued. Making a request such as this is attempting to engage in software piracy and this forum cannot be involved or associated with this activity. The same goes for any private transaction via Private Message. Even if you attempt to engage in this activity in PM's we will still enforce the forum rules. Your PM's are not private and the administration has the right to read them if there's a hint to criminal activity.
If you are having trouble legally obtaining software please state so. We do not want any hurt feelings when your vague post is mistaken for a free request. It is YOUR responsibility to properly word your request.
To obtain Motorola software see the Sticky in the Motorola forum.
The various other vendors often permit their dealers to sell the software online (i.e., Kenwood). Please use Google or some other search engine to find a dealer that sells the software. Typically each series or individual radio requires its own software package. Often the Kenwood software is less than $100 so don't be a cheapskate; just purchase it.
For M/A Com/Harris/GE, etc: there are two software packages that program all current and past radios. One package is for conventional programming and the other for trunked programming. The trunked package is in upwards of $2,500. The conventional package is more reasonable though is still several hundred dollars. The benefit is you do not need multiple versions for each radio (unlike Motorola).
This is a large and very visible forum. We cannot jeopardize the ability to provide the RadioReference services by allowing this activity to occur. Please respect this.
XTS 1500 NO RX
- Thread starter rich1125
- Start date
- Status
mmckenna
I ♥ Ø
Sounds like you have the DPL set incorrectly on the RX side. Confirm the setting in the repeater and make sure it matches what you are programming in to the radio.
As for the "bleed through" of the Taxi company, are they licensed on the same channel as you?
Do you have your channels set for 12.5KHz/2.5KHz deviation?
As for the "bleed through" of the Taxi company, are they licensed on the same channel as you?
Do you have your channels set for 12.5KHz/2.5KHz deviation?
mmckenna
I ♥ Ø
If the LED lights up on your radio when the repeater is transmitting, then the receiver is hearing it. Something is keeping the squelch closed. Usually it's the PL or DPL set incorrectly.
As for your Unmute/Mute rule, should be set to Std Unmuting, Std Muting, unless you are using some form of paging.
As for your Unmute/Mute rule, should be set to Std Unmuting, Std Muting, unless you are using some form of paging.
NO FORM OF PAGING JUST MDC IT SHOWS ON MY OTHER RADIO 703 DPL WHICH IS A HT 1250 WHICH IM BAFFLED BUT I DO HAVE IT SET ON UNMUTE / STD MUTE I DOUBLE CHECKED ALL RX /TX DPL CODE REPEATER ON FCC IM LOST SOUNDS CRAZY BUT IT HAPPENING . SHOULD I TRY MIXED MODE .
MTS2000des
5B2_BEE00 Czar
YOU DON'T HAVE TO SHOUT
Ahem...if the DPL/PL mute rule is set to "standard" and other subscribers unmute, than it's possible your XTS needs an alignment. The XTS/XTL are also very sensitive to DPL deviation, if it's too low, it will ignore the code and remain muted if RX is set to decode.
Ahem...if the DPL/PL mute rule is set to "standard" and other subscribers unmute, than it's possible your XTS needs an alignment. The XTS/XTL are also very sensitive to DPL deviation, if it's too low, it will ignore the code and remain muted if RX is set to decode.
sorry i hit caps lock
FKimble
Member
Just remove the tone. It ain't gonna help the bleed over.
Frank
Frank
so just take the rx out and put it to csq i think i will cant figure out why it will not work sounds crazy never had this before.
That is normal operation if you have another type of signalling squelch enabled. You mentioned MDC. Do you have Sel Call enabled?
i think i do let me look.
yes i do have it enabled i forgot to also put its a 1.5 model. could that be the issue i have it set to sel call .set to std mute dpl are all correct and i have it set to non astro im just baffeled .any help wold be appreciated.
In your personality if either Sel Call Decode or Call Alert Decode is checked, then uncheck it.
ok im on it now thank you
het frank you helped me awhile back on my xts 1500 rx issue i have on csq it works great got it tuned alinment but if i put tone in agian no rx , i dont mean to beat a dead horse but could the board be bad . thanks richard
Is the tone correct?
yes i pulled the codeplug from another radio all correct .
mmckenna
I ♥ Ø
Who tuned/aligned your radio?
If the 'board was bad', then that would have been discovered during the alignment process.
Compare your codeplugs carefully. If the HT1250 works, and you copied the settings —exactly— then there's an issue with the radio.
If the 'board was bad', then that would have been discovered during the alignment process.
Compare your codeplugs carefully. If the HT1250 works, and you copied the settings —exactly— then there's an issue with the radio.
- Status
