Hello All, I'm installing a Kenwood TM-V71A into my 2000 Chevy S10 and was wondering if anyone had a suggestion for the best place to go through the firewall with the power cables? Thanks in advance.
-
To anyone looking to acquire commercial radio programming software:
Please do not make requests for copies of radio programming software which is sold (or was sold) by the manufacturer for any monetary value. All requests will be deleted and a forum infraction issued. Making a request such as this is attempting to engage in software piracy and this forum cannot be involved or associated with this activity. The same goes for any private transaction via Private Message. Even if you attempt to engage in this activity in PM's we will still enforce the forum rules. Your PM's are not private and the administration has the right to read them if there's a hint to criminal activity.
If you are having trouble legally obtaining software please state so. We do not want any hurt feelings when your vague post is mistaken for a free request. It is YOUR responsibility to properly word your request.
To obtain Motorola software see the Sticky in the Motorola forum.
The various other vendors often permit their dealers to sell the software online (i.e., Kenwood). Please use Google or some other search engine to find a dealer that sells the software. Typically each series or individual radio requires its own software package. Often the Kenwood software is less than $100 so don't be a cheapskate; just purchase it.
For M/A Com/Harris/GE, etc: there are two software packages that program all current and past radios. One package is for conventional programming and the other for trunked programming. The trunked package is in upwards of $2,500. The conventional package is more reasonable though is still several hundred dollars. The benefit is you do not need multiple versions for each radio (unlike Motorola).
This is a large and very visible forum. We cannot jeopardize the ability to provide the RadioReference services by allowing this activity to occur. Please respect this.
2000 Chevy S10 firewall
- Thread starter KG4INW
- Start date
- Status
Pull back the carpet on the passenger side of the truck where it meets the firewall. There should be a plastic wiring channel. Above the channel you should see a big rubber grommet for the antenna coax. This is probably the easiest spot to run a wire or drill another hole. Its a bit low on the firewall so make sure you seal it well.
mr_tunz
Member
Driver side is usally a good place to go. There is always extra space on the driver side and ur not dealing with the huge heater box. There room in the harness that run up to the engine.
Alright, thank you very much! I'll poke around some more when I get some time.
If you s10 is manual tranny then you will need to find a grommet or drill a new hole. However if the s10 is an automatic look for the block off plate where the master cylinder for the clutch would be and you can put a hole in there. Good luck with the install -JOEYD
MECP Advance Installer
MECP Advance Installer
Thanks again for the tips. I was able to go through an existing grommet on the driver's side and it has been working very well for me. Very satisfying to finally finish.
Where exactly is the grommet you found to use?
I used the same grommet that the main wiring harness goes through. There's a lot of extra space to the left of the main bundle and although the rubber's pretty thick and interior access is tight, it wasn't too hard to work with.
tmfok7
Member
So you have to post a picture of the install! I have a TM-V71 too and have some ideas as to what I want to do but always like see other peoples work.
bep
Member
I second tmfok7 request. Very tight for mounting anything in this truck. Looking for ideas.
OK, I'll post pictures as soon as I can get to the truck! Probably tomorrow.
Whew, sorry for the delay so here are some photos of the radio in my truck. It's mounted on a CB console that I bought from Mobile Music in Richmond. I have no idea what brand it is though. Cost $20 and I like it because I can put the radio in and take it out real fast so I have the comfort of knowing it can't be stolen when the truck just sits there for long periods. The other mount you see is for my CB that wasn't in there when I took the picture.
Attachments
Looks good 1 ... was wondering if your gonna try to tuck the wires and cable !
Thanks. The wires and cable that you see in the pic is all that's visible and the CB covers it up pretty well. What's not visible is the split-loom tubing I used to protect the coax cables.
- Status
Similar threads
