dsd+ fastlane

I checked my DSDplus.LRRP file and found: 2019/01/07 16:38:04 3040038 32.44028 10.11125 2019/01/15 10:36:43 3091007 30.24327 31.03325 2019/01/15 10:51:39 3700016 23.47263 39.40114 2019/01/16 16:18:57 3040003 32.61569 32.61605 2019/01/18 14:03:27 3059018 32.81953...

HI, I am new to the whole DMR decoding thing, hunting for DMR LRRP messages. Equipment: DSD+ 2.169 Fast lane, using FMP Motorola DP4801e Hytera PD785G Hytera Dispatch software RTL-SDR dongle Simplex channel, no repeater. I see raw data requests and replies in a DSD+ window. I see GPS locations...

There is a specific repeater I tuned to on FMP24 but the decode is very bad but the signal itself looks sufficient and more than enough for dsdplus to decode. I have used different tuning options by using dsdtune and used different filtering options but in this recording I have I used 7.6 khz BW...

Complete newbie. Two files attached - log files. Use three RTL SDRs and the following bat files: FMP24 -i2 -o20003 -P0.0 -s1 -b4 DSDPlus -e -fr -i20003 -o1 I have a scanlist and frequencies files populated and correctly formatted with the same frequencies obtained from here: Digital...

I'd like to do a fresh start on DSD+FL. I got a couple of airspy units and had previously removed the airspy files from my setup. My first available update was 2.98, then 2.113, then 2.145, and now 2.155. I no longer have access to 2.98, 2.113, or 2.145. What's my best option to do a full...

I started this endeavor with unitrunker and DSD+. I was having issues with a lot of decoding errors. The audio sounded like horrible autotune. It was suggested on these forums to ditch unitunker and go completely with DSD+ Fastlane. Now I have gone fully with DSD+ Fastlane. Everything seems...

Is it possible to surpress the weird/annoying background wind sounding audio in dmr when someone stops talking but is still keying up? It sounds like wind and it sometimes overcomes someone's voice on some comms usually for some reason the dispatchers. I have tried many advanced commands to...

Just wanted to give a shoutout to the author of DSDPlus. I *finally* took the 5 mins to insert my 2nd RTL-SDR v3 dongle and got trunking working. So far I have successfully and easily tracked a CON+ system (with frequencies manually entered) and a P25 site without issue! So...THANK YOU. This...

(((EditToAdd: Newbie replies are in purgatory, but upped a new pic of CPU running pretty low. Also, I wasn't clear, but I am using UniTrunker to feed DSD+. Also: With great thanks to mtindor I think I am wrestling with this...

Is it possible to have the information with DSD on XPT networks as with Motorola C + networks. Radiotrbo

I've been monitoring a system which I think is mainly Conventional DRM and I would like to have your experienced input on this. I've devised a kind of recording system; recording all DMR activities on the specific channel 24/7 all around. Using SDR# with AUX VFO plugin, it starts recording in...

Hello, I have been having good success with DSD+ 1.101 with various 820T2 receivers. I recently upgraded to the Fastlane version, however, it doesn't work for me. I'm using this to monitor a multi-site DMR Con+ system. The receive in FMP24 looks fine, and the waveform in the receive window...

Hello folks! I'm having a little bit of an issue here. I have the subscription-based DSD+ FastLane w/ current version 2.39 and current FMP24 version. The issue I'm having is I can't seem to get the Over-the-Air Aliasing to work properly... My signal is good, no errors showing, and it's...

I can't get the program to exit by pressing ESC. The decoding just stops and at least one time a line reading "writing .bin file" or similar appeared. The only way to exit then it is to click the "X" at the upper right corner (F4 doesn't work either). I'm using a 64-bit Windows 10 PC. I thought...

FMP24 2.19 does not honor -b-<kHz> parameter "Set initial RF filter bandwidth and ignore hints from DSD+" when utilizing Output audio device. Works as expected with TCP. To reproduce launch FMP24 2.19 then launch DSD+ 2.39, modify bandwidth and and watch it change automatically. Here are the...