minitor

I have recently accepted a position as a photojournalist for the midcoast region and I want to get my Minitor 5 programmed professionally for the various fire services. I have scoured the internet and cannot find a local provider of such services. Does anyone know where I could go to have this...

I want to buy a used pager and I want to switch the frequencies and alert tones. Are minitor IV's re-programmable in that sense? Any help is greatly appreciated!

Ive gone through multiple minitor 3's and I am now realizing that something is wrong. Initally i had a minitor 3 that I was reprogramming atleast 2 times a month. After a while it was constantly squelching when on open scan(C Switch). After a while i relized that this was would only happen on...

I have two Minitor V VHF 2Ch. Stored Voice pagers. 1. The first is a bit beat up and I wanted to take it apart to clean the contacts. In doing so, I turned what appeared to be a screw on the circuit board that crumbled exposing a red coiled wire. The pager has not received audio since I...

This is my first post on RadioReference, so I apologize if I post this under the wrong section. I work in El Paso, Tx for the general hospital. In my hospital, we use the US Alert Nova pager to alert the Code Blue/Rapid Response teams of cardiac arrests or incoming traumas brought in by EMS...

I am attempting to program a Minitor 4 pager and am running into a problem placing it into programming mode. I turn off the pager and hold down the sqealch button. I turn the pager on while holding the sqealch button and I only get a single yellow light. The guide says I should get two lights...

First, I apologize if this isn't the right forum for this post. I have an old Motorola Minitor II pager. I would like to purchase a crystal (crystal?) for it to monitor 154.175 frequency when I'm out and about. Will that do the trick, or do I need something more? Also, can someone point me to...

If I have Minitor III that is tuned for 460MHZ, is it possible to change the receiver board so that it can be tuned to 425MHZ? Or better yet, is there a way to tune the 460Mhz receiver so that it picks up 425Mhz? NTFD67

Good Morning All, I tried to search this on the forums but didn't find any info. My Minitor 5 is UHF with a Split Band of E. I need to change this to a K Split Band, so it can be prg with our new freqs (495's -496ish) Does anyone do this, or know where I can get a new board or have it...

I'm looking for a list of the station/fire pager tones in Lee County Florida. I haven't found much for this county, although I was able to find a complete list of tone outs for Collier County. Does anyone know of any resources for this information? Thanks!

im programing a motorola minitor v i put channel D to priority scan problem is its not open if i hold the reset button down than it becomes open an i can hear. i have the squelch set to 3 tried 5 and 1 and nothing anyone know what the problem is thanks

Does anyone know where I can get a Motorola Minitor 2 pager programmed? For years my brother was a volunteer fire fighter but do to a back inquiry he had to quit. He also had to give back his Motorola Minitor 2 fire pager as it was such a small company there were not enough to go around...

Please help, I have a minitor 3 and I have programed it to my specific two tone frequency, the problem is that another house has a similar group call and when they are toned out my pager goes hay wire.. I don't know if it's because the tones are to close to each other? or my maybe their is...

Hello all, I am programming a used Minitor V pager, and have noticed that the volume setting for both alerts & regular radio traffic is fixed on the minimum level. No matter how high I turn the volume knob, the beeps and voice does not change volumes. The fixed volume alert option is disabled...

Have a question on how to set up the Minitor III and IV's. I have both pagers and they are both 2 channels my question is im trying to set up the 4 switches A is medic 911 page and all call (duty off) B is medic All call (duty on) i need a switch where i can scan both channels to have it...

Okay so you have a dual channel minitor v the question problem is when you get back to back alerts on each channel the other channel wont alert. so lets say you have channel one ems and channel two fire the fire pages out on channel two you get the alert then a second later with (red light...

I'm switching to a minitor v from a minitor II. My question is I have 3 tones for the minitor II but when you program the minitor V you only have 2 call tones tone1 and call tone2. So how you go about this?

Can anyone tell me where I can buy aftermarket minitor 3 housings?

Is there anyone that has, and would be willing to send me, the tone out tones for Tolland county? Specifically I am looking for the Vernon tones, but would take all available. Just want to be able to set the tones in my BCD-996t to keep the thing from keeping me up all night. The Minitor just...

Hey, I know that some of you out there have Motorolas Minitor V pager I am looking for a user guide/manual for it I have searched google dozens of pages back and can only find the brochure If anyone out there can scan the pages or give me a link to download the user guide/manual it will be...