Junie55
Member
Yes. I found 153.2000, but since it is already listed in the database as Site 110, I ignored it.
OFFICIAL NYSEG P25 System Thread
- Thread starter rbm
- Start date
- Status
Junie55
Member
For 153.2000 it displays SID:0269h-0110
Junie55
Member
I looked at the update and you have Jasper listed in Allegany County. Jasper is actually in Steuben County. Hope this helps.
Clay
Clay
D
DaveNF2G
Guest
I did not look at the updated info, but as a point of information, the place in Cattaraugus County is Olean. Orlean and Orleans are elsewhere.
A simple typo on my part in this thread (I did get it right in my first post, in case you missed that), however I entered the correct spelling in the database. I don't suppose it would've killed you to take 5 seconds to check the database update, if for no other reason than to make sure it was correct there? :roll:
rbm
Member
Deleted
Last edited:
rbm
Member
D
DaveNF2G
Guest
Why did this thread get un-stickied?
rbm
Member
As long as it's back at the top, here's a screen capture of some NYSEG control channels using an SDR dongle and SDR#.
It makes finding CC's a lot easier.
There's a pager at 152.180, otherwise most of the signals are NYSEG CC,s.
Rich
It makes finding CC's a lot easier.
There's a pager at 152.180, otherwise most of the signals are NYSEG CC,s.
Rich
Last edited:
153.185 wells hill Lewis NY essex county wont decode on 3 scanners
WQQV887 (NEW YORK STATE ELECTRIC & GAS CORPORATION) FCC Callsign Details
NYSEG PHASE 2?
8K10F1W
home patrol 1 shows no raw data info
396xt no Control Channel output
Sounds like a Phase 1 control channel but only lasts for about 5 to 10 minutes bursts every 1 to 2 hours.
Is this something new NYSEG is going to be doing with their new site installations...
Is anyone closer to Wells Hill That can try and monitor and see if they can get any info off the site and confirm whether or not its phase 2
WQQV887 (NEW YORK STATE ELECTRIC & GAS CORPORATION) FCC Callsign Details
NYSEG PHASE 2?
8K10F1W
home patrol 1 shows no raw data info
396xt no Control Channel output
Sounds like a Phase 1 control channel but only lasts for about 5 to 10 minutes bursts every 1 to 2 hours.
Is this something new NYSEG is going to be doing with their new site installations...
Is anyone closer to Wells Hill That can try and monitor and see if they can get any info off the site and confirm whether or not its phase 2
D
DaveNF2G
Guest
Probably something other than voice communications.
SargeUSMC
Member
At this point, is there a master compilation of sites/frequencies/talkgroups and any other information that someone may have put together that they'd like to share??
Like this, or something else?
New York State Electric and Gas (NYSEG) Trunking System, Statewide, New York - Scanner Frequencies
New York State Electric and Gas (NYSEG) Trunking System, Statewide, New York - Scanner Frequencies
rbm
Member
I don't think much has changed recently.
I ran Pro96Com and Unitrunker just last week for the sites I can receive, with the following results.
Rich
CC Sorted By site:
101-T0101 153.2600
103-T0103 153.7175
104-T0104 153.6425
105-T0105 152.0975
106-T0106 153.1475
107-T0107 152.1425
108-T0108 152.5325
109-T0109 152.0825
111-T010B 152.7875
112-T010C 152.2175
113-T010D 152.5025
115-T010F 152.0225
117-T0111 152.5475
118-T0112 152.7425
119-T0113 153.3125
123-T0117 151.9700
124-T0118 152.7125
139-T0127 152.5175
Sorted by CC Frequency:
123-T0117 151.9700
115-T010F 152.0225
109-T0109 152.0825
105-T0105 152.0975
107-T0107 152.1425
112-T010C 152.2175
113-T010D 152.5025
139-T0127 152.5175
108-T0108 152.5325
117-T0111 152.5475
124-T0118 152.7125
118-T0112 152.7425
111-T010B 152.7875
106-T0106 153.1475
101-T0101 153.2600
119-T0113 153.3125
104-T0104 153.6425
103-T0103 153.7175
Last edited:
SargeUSMC
Member
- Status