icom

TrunkPCR version 0.90.286 Now Available for Downloading from the Homepage: Trunk Tracking PCR NOTE: Moto Type-I Support *should* be finished in the next major update. This update has Six Fixes and One Addition... Oct 12,2012 - Fixed: Setting CTCSS Tone Option as Normal instead of Reverse...

Guys, I`m looking to upgrade a batch of UT-119H Modules to UT-126H status. Can anyone help out with the Firmware update to carry out this Mod. These units are being fitted to a batch of IC-F5061/2 which have been programmed with v2.6 software.

I have heard that UT-119 Modules can be upgraded to UT-126H. Can anyone help out with the Firmware?

Hi Could anyone who has the ICOM IC-RX7 please answer this question? If there was a specific amplified speaker specifically for the RX7 what features would you like/expect it to have, and why? Thank You for your time much appreciated!

Hello ALL A seller told me that ICOM has discontinued manufacturing new IC-V82 sets? I tried to google and also visited ICOM website but could not corroborate it? So is this true or only a ploy to sell alternate sets? Thanks in advance! -- AHammer

Hi, I have an Icom IC-F70DT & IC-F80DT. Both have the following firmware versions: Rev 3.0 / P25 Rev 2.8u. My Icom programming software is CS-F70/F1700 Version 2.2. I recently joined an amateur radio group that requires MDC1200 for access (FishFAR in Chicago). It requires a 1200ms delay...

So, I have my F-6021 UHF radio programmed with all of the channels that I need. I have a few repeater channels that require a PL tone, however I do not see a field in the channel programming page where I can insert a PL tone. Also, I would like the radio to transmit a courtesy beep, or a roger...

I just bought an ICOM IC-211 VHF (2 meter) All-mode base rig on E-Bay. Power turns on, but neither VFO lights. Does anyone have any ideas or can you recommend an ICOM repair shop that is affordable? 73, Gregg, N2UUP

About a week ago I noticed my the ant tuner for my 706 mkIIg installed in my truck was making a clicking sound without any equipment powered up. I unplugged the 12VDC to the radio and the noise stopped. A day or two later, when I had some time, I tried to do some troubleshooting when I noticed...

Has anyone ever tried replacing the front case on an Icom IC-F80DT? I have downloaded the service manual, and have found the part number: 8210021800 - 2803 T-Front Panel (IC-F80DT/T) The disassembly looks to be straightforward enough, but it's always nice to learn from someone who's done it...

I hope I am posting this in the correct forum? I have the ICOM IC-V8 Handheld and I bought it pre-programmed from a fellow Volunteer FF. Now that we are switching to NarrowBand, I need to hopefully find someone that can help me to switch it from Wide to Narrow Band. I did pull the manual...

Hello to all I am just starting this discussion on my own curiousity. I have recently left emails and messages with many large scanner and 2 way radio companies. I inquired by all companies why there is no rugged water /dust/ impact resistive scanner on the market. For instance take a...

After a few weeks, we had very good testing results w iCOM digital HTs (ICF4161D) at the local office. Exceptional audio clarity in digital simplex mode compared to when we step back to the analogue world repeaters. So the boss said it's time to step up to IDAS Repeaters! Btw, the digital...

Made a little video of it performing tonight. I haven't used it in a while. Another great railroad radio. If you have any questions, please post them. Metrolink Valley Subdivision Radio - YouTube

I have a F5061 with a handy 25-pin dsub connector on the back. I know Icom sells a GPS unit that plugs into it, but I cannot find any documentation on the pinout for that connector. I think one of the pins is a dimmer and I would like to use that. If anyone has used this connector or can point...

I am removing a gm-300 from one of our trucks that has 2 mic's connected through the 8 pin connector. I would like to install the new 5061 and keep the same configuration. I am wondering what pins need to be connected for this.

Does anyone know if the Icom IC F121 radio will transmit or receive on a 400 MHZ frequency? I put one in and set it as primary and when the radio is not scanning or I try to key it it blinks the frequencies ID on the screen... Is this because it won't accept the 400+ frequency or because I have...

Shipping to Canada, please. Thanks :)

Well, I decided to purchase the Icom R6. And so far, I just love this unit. Sound quality is excellent (better than the RX-7). It is small just like the R2 and R5. But by far, my favorite aspect of this radio is the impressive sensitivity. I am able to receive from Warren PA North, down to...

So I have a Astron 30 Amp power supply and a 25 amp Power supply. When the Icom 706 is connected to the 30 amp power supply the radio will shut off when the power setting is above "3" The volts on the power supply decrease to around 6 and the Icom will shut off. When I attach it to the 25 amp...