icom

Hello all, I'm planning on getting a R-75 soon and want to be prepared by having a good antenna for it soon as possible. I usually monitor utility stations, military freqs, aircraft, number stations, hams, unknown signals, and commercial broadcasts, as well as DXing for signals. So pretty much...

Is there a way of telling exactly which segment of the UHF band this radio covers? When programming, I get a CL good indication from the radio, but some frequencies flash, and others TX but not RX. Serial no. is 107163 if that helps. Thanks, Gregg, N2UUP

Hi! I have a question about my ICOM IC 2-GXAT. I've had it 20+ years and it's traveled all around the country with me in planes, trains and automobiles and it worked flawlessly. It's old and it's single-band, but it does the job. The only thing I've ever had to do is replace a battery pack...

Hi all, in need of assistance. I have 6 ICOM IC-F3021S portable radios, that are in need of programming. Before anyone throws at me for not being a "licensed ICOM tech., I understand, and do not need that as answer, or "take it to a certified dealer". That's not why im here. I have acquired...

After an exhausting search (to no avail), for a schematic to make a bypass plug for an Icom F121 I decided to figure it out for myself. I wanted to basically use the radio as a scanner without the possibility of it being able to transmit as it is sharing a receive antenna with other receivers...

I have an ic f4001 and a usb programming cable. I have the CS-F3000 program, and the Proflic PL 2303 driver. Whenever I try to connect an error pops up that says "Cannot Access COM (whatever number I have selected)". It does this regardless of whatever COM Port I have selected. Any ideas on...

My Icom IC-R71A was having some 'strange' problems, and I've traced one problem as the negative ten volt supply on the 'Matrix Board' being inoperative. Failure of this PS is noted in the Icom troubleshooting guide as affecting the audio output and S-meter. So, I have disconnected the...

Hi I have a F51V(Handheld), It can be transport information by RS 232C Port.(I have other equipment send and receive the information by RS 232 port.) Now, I want to look for a new equipment for transport the information like F51V. I find a setting in the F51V for the transport information, at...

So I'm a total noob when it comes to ICOM. I'm normally a Motorola man, but since I heard about the railroads slowly going to NXDN, I decided to invest in my first ICOM since I'm a train buff. I got the software from theantennafarm, along with an F3161 with a keypad, and a cable, etc. Basically...

Kenwood

I have an Icom IC-756 ProIII for sale. Come's with: Factory box, All paper work, CW KeyJack and Accs Plug, Extra fuse pack, Stock hand mic and Power cord, Icom PS-125 power supply with original box, SP-21 Speakers and MFJ-392 headphones with original box. (All original pack unopened from...

Please help me with this. I have an Icom f510, which after a forum strand on here I managed to get transmitting. I have today had to reprogram it updating the frequencies. Now the radio will receive when on the correct channel, but pushing the PTT results in the radio returning to channel 1...

ICOM 775-DSP radio. I am the original owner and a Non Smoker. It comes with the HM-36 mic, UT-66 Voice Synthesizer unit, ALL optional filters installed, CT-17 remote control interface cable, accessory bag, custom sound card interface cable for PSK-31 & Rtty modes. Radio also comes with original...

Hi! I have an ICOM IC-R2500 connected to a long wire (20Mtr braided steel core, plastic coated washing line) terminated at ground level outside through a 9:1 UNUN Transformer, grounded via a 4ft solid earth rod in soil less than 2ft from the termination box. something similar to RG6 coax...

I have a V-8000 Radio and then I have CS-8000 programming software that I purchased. I downloaded the software, but I'm having problems trying to clone or program my radio, for some reason the radio or programming cable are having troubles communicating. I've set the COM Port to "1" which isn't...

Hello everyone! I’ve been out of ham radio for a while and have recently decided to explore getting back into it. While I thought I had sold all my ham gear, recently I found my old Icom IC-2AT. From what I can tell, both the transmit and receive audio are low. I don’t think other stations...

The F2721D is a great radio for a ham because it not only offers you UHF FM operation, but also P25 Digital Operation. Included in this complete package are all of the following items in like new condition: Icom F2721D P25 Digital Ready 45 Watt UHF radio 400 – 470MHz (upgraded to the latest...

Hi All, I am helping setup a radio infrastructure and I need some opinions as to the best way to get this done. Here is what the situation is and sorry in advanced if I ramble on a bit. This will be a 4 site system in the middle of nowhere, in the forest, so we want to go with a trunked setup...

Hello, I use a mobile radio at work icom either F5061 or F6061 I'm not exactly sure which one I dot have access to the label it's installed in te vehicle. My problem is periodically I cannot transmit and it says "Failed E213." I have tried looking up what this error is but cannot find any...

Hello, I just bought an Icom IC-F1721D UHF mobile radio, and I would like to get a copy of the service manual. I have had no luck searching for it on GOOGLE. My email address is: dmascarella@ymail.com. Thanks for your help!