OldRabbit
Member
- Joined
- Jul 15, 2020
- Messages
- 73
Hi, sorry for asking another DSD+ question, but the posts I have been able to find on the subject does not quite answer my question.
I have Purchased and installed DSD+ Fastlane - and using SDR# + VBCable in my setup.
I am able to tune into a digital frequency - and see some response from DSD+, but so far - I have not been able to decode any audio.
To get a known DMR signal, I added a simplex channel to my TYT UV-380 radio and used that as a test transmitter.
Getting any reaction in the DSD+ window is a hit or miss, when I do, I get a list of +DMR lines scrolling, sometimes a Voice header.
So question:
Is it correct, that I should be able to decode and listen to the voice from a DMR handset using DSD+ Fastlane ? - all the videos I have been able to find are using repeater frequencies but that should hardly make a difference ?
Also any documentation on the settings of the Input, Output, Decoder and Control options in Fastlane ? - the readme is very brief.
Update - managed to capture some output - created when keying and talking in my UV-380:
Mono audio decoding initiated; press Esc to exit...
Sync:+DMR
+DMR MS DATA ERR3 DCC=13 Idle ERR100
Sync: no sync
Sync:+DMR
+DMR MS VOICE e:7r7r4r
Can't append to incompatible file 'DSDPlus.wav'
Can't append to file 'DSDPlus.wav'; trying create instead
+DMR MS VC2 e:7m7r5r
+DMR MS VC3 e:6r7m5e
+DMR MS VC4 e:6r7r7r
+DMR MS VC5 e:6m6r7r
+DMR MS VC6 e:6r5m6r
Sync: no sync
Sync:+DMR
Sync:+DMR
+DMR MS VOICE e:7r7r7r
+DMR MS VC2 e:4m5r6r
+DMR MS VC3 e:5r6m7e
+DMR MS VC4 e:6r5r6r
+DMR MS VC5 e:7m7r6r
+DMR MS VC6 e:6r4m7r
+DMR MS VOICE e:6r6r7m
+DMR MS VC2 e:5r7r6r
Regards
I have Purchased and installed DSD+ Fastlane - and using SDR# + VBCable in my setup.
I am able to tune into a digital frequency - and see some response from DSD+, but so far - I have not been able to decode any audio.
To get a known DMR signal, I added a simplex channel to my TYT UV-380 radio and used that as a test transmitter.
Getting any reaction in the DSD+ window is a hit or miss, when I do, I get a list of +DMR lines scrolling, sometimes a Voice header.
So question:
Is it correct, that I should be able to decode and listen to the voice from a DMR handset using DSD+ Fastlane ? - all the videos I have been able to find are using repeater frequencies but that should hardly make a difference ?
Also any documentation on the settings of the Input, Output, Decoder and Control options in Fastlane ? - the readme is very brief.
Update - managed to capture some output - created when keying and talking in my UV-380:
Mono audio decoding initiated; press Esc to exit...
Sync:+DMR
+DMR MS DATA ERR3 DCC=13 Idle ERR100
Sync: no sync
Sync:+DMR
+DMR MS VOICE e:7r7r4r
Can't append to incompatible file 'DSDPlus.wav'
Can't append to file 'DSDPlus.wav'; trying create instead
+DMR MS VC2 e:7m7r5r
+DMR MS VC3 e:6r7m5e
+DMR MS VC4 e:6r7r7r
+DMR MS VC5 e:6m6r7r
+DMR MS VC6 e:6r5m6r
Sync: no sync
Sync:+DMR
Sync:+DMR
+DMR MS VOICE e:7r7r7r
+DMR MS VC2 e:4m5r6r
+DMR MS VC3 e:5r6m7e
+DMR MS VC4 e:6r5r6r
+DMR MS VC5 e:7m7r6r
+DMR MS VC6 e:6r4m7r
+DMR MS VOICE e:6r6r7m
+DMR MS VC2 e:5r7r6r
Regards
Last edited: