Unitrunker 1.0.0.9

[SCPD]

This is a mini-release to fix the EDACS group ID problem reported in versions 1.0.0.6 through 1.0.0.8. There are no other changes, fixes or improvements at this time.

Downloads

 

[DiGiTaLD]

Tried to extract it. The extraction process claims that Uniform is a password protected file. O noes!

EDIT: Disregard. Not sure what caused that, but I just got it to extract successfully.

 

[Muxlow]

Seems to of been fixed on my end
This was for the TG's showing up wrong and patches? Like Patch TG 702 should be 1972 or something like that?

 

[sammycookie]

Thank You Rick its works fine for me.

 

[Forts]

Seems to of been fixed on my end
This was for the TG's showing up wrong and patches? Like Patch TG 702 should be 1972 or something like that?

Yes, I believe so.

 

[mobile1]

1.0.0.9 is working great here on the local FleetNet800 EDACS site control channel. Thank you Rick.

 

[ke5fgc]

when i try to import from the Retro version it crashes every time. Any ideas?

 

[Jay911]

Corruption in a data file? Does unitrunker.xml get written? If so, if you examine it, you might be able to figure out the "last" system that was imported and/or which one is crashing it.

 

[SCPD]

when i try to import from the Retro version it crashes every time. Any ideas?

I think I have a fix for this. I found a problem while importing some old data from 2004-2005. I'll let everyone know.

 

[FlashSWT]

I just noticed that in 1.0.0.9 talkgroups I have set to "Blink" are no longer doing so. They worked fine in whatever the last version was (1.0.0.5?) that I was using for a long time before all the recent updates.

.

 

[mws72]

Wirelessly posted (BlackBerry7250/4.1.0 Profile/MIDP-2.0 Configuration/CLDC-1.1 VendorID/105)

After running 1.0.0.9 for a couple of days. First keep up the great work.


My comments are: EDACS TG numbering back to normal. However now the signal is very low showing only two red bars and seeing missed or mis-decoded RIDs.

I went back and ran 1.0.0.6 and it showed full strenght.

For moto type IIi. Other than not showing type I TGs (all show as type II) it is now showing type II radios RID as the what the TG id is. When I run UT-retro and Trunk88 along side 1.0.0.9. I will see a type II change to the TG id fast (if you blink you could miss it) example a Type 1 id is 113-1. A type 2 radio id for that TG is 58881 this is instead showing as 14912 same as the what the program shows for the talkgroup.

 

[gator]

Hey Rick still unable to get the band plan in here is a pic of what the channels(after RR download) look like without the band plan in there.Is there a reason why the Band plan dont download from RR with all the other data?

 

[stummej]

Maybe im just dumb but i for the life of me cannot get my 396xt to connect with Unitrunker.

settings are:
Inline,BC396xt,Signal,Running,Com4,115200,8,1,None

Scanner is set to extended output for control channel, am I doing something wrong here?

 

[SCPD]

I doing something wrong here?

No. Decoding from the "XT" Uniden models is broken. No ETA at the moment as to when this will be fixed.

 

[DaveNF2G]

You might already know this, but UPMan's twiki page at Uniden has a revised XT protocol document linked at the bottom of the firmware updates page.

 

[DiGiTaLD]

Just an update from here after using the latest version of UT since it's release almost non-stop except for routine automatic system updates: much more stable and reliable - I don't think its crashed even once. Whatever problems there were with stability in 1.0.0.6 and earlier seem to have been resolved. Thanks again for the great work on this software Rick.

 

[SCPD]

There's an awful volume control bug with the newer Uniden models. The program sends the radio to max volume at start up. Ouch. Anyone else noticed this?

 

[Jay911]

On the contrary, I have noticed that the program mutes (or at least sets to zero) the volume on my 396XT. Haven't tried it for a while.

 

[Zack08]

I upgraded to this version after using the old text-only unitrunker for a couple years, and its leaps and bounds better, but I cant find a way to use a dataslicer with it. Has that feature been dropped in the new programs, or am I just missing it?

I used to like using a slicer because it would allow me to run other software on the soundcard at the same time....

 

[SCPD]

Has that feature been dropped in the new programs

Slicers are a pain in Windows. The slicer option in Unitrunker Retro was Windows 2K/XP only. As a cheap fix, you could buy a USB sound adapter.