programming

Apologies in advance. Coming from a Radio Shack Pro-60 AM/FM scanner, this new SDS100 is mind boggling. Please point me to a SDS-100 101 link. Objective #1 - Learn the basics of how to manually create a FL, and determine what is required, or can be ignored. Objective #2 - Manually program a...

FYI..successful in programming BF GM 15 Pro with TIDRadio Wireless Bluetooth Programmer. Although it said that device software driver was in beta it worked like a charm. The app is okay, has some quirks but much much better than hand punching channels to monitor. I gave up desktop computers and...

I have a question about programming a system into a radio or scanner. In the table below, it shows 2 frequencies that are the same, under slot 1. Then you see 2 frequencies that are the same under slot 2. I'm not sure I understand this. It's a dmr system. My understanding is that DMR trunked...

I have a strange problem with my mobile radio Motorola DM3601. It was working perfectly fine and I could program it normally, until I wanted to try controlling it remote with gpio controlled channel steering TX/RX. After the last programming of the radio and my successful tests, the radio is no...

Hello all, I’m trying to just program in some channels for receiving my local ems agency as well as repeaters and simplex T/A channels. I just started with trying to do the ems agency ones for receive only. The channels are analog conventional. I have 1 Zone, 1 System, and 1 Conventional Set...

I have a CM300D that I am trying to get set up for DMR use. I have the CPS software, as well as the software user's guide. I am new to DMR, and for the life of me I can't grasp the formatting. I get to the contact set and get lost. Is there a .csv file that uploads into the radio, and is such a...

Bought a couple used XTS2500's. I have a good knowledge of how to program my radios in CPS. However both radios came with over 94 conventional personalities across 6 zones that I am unable to delete, I learned that I am unable to delete them in CPS due to FPP being enabled. I am trying to figure...

I’m located in Concord, NC. Is there anyone in the vicinity, who would be willing to program or educate me on how to use CPS, for a HT1250 LS+ Thank you.

Hello. I'm new to the forum and I apologize if this thread is in the wrong place but I'm kind of frustrated and borderline desperate. first off, I'm trying to get a PD362 and PD 782 to work but I need software called Flashburn v9 to finish the process, I tried the 3/5 but didn't get anywhere...

Hi All I have an issue with my new BP565's. I have programmed them to Simple UK Analogue frequencies so that they both talk to an existing fleet of analogue radios. This is working fine and all radios can recieve and transmit to eachother. I would like to be able to have a private call...

Hi, I'm trying to update the firmware on a PD565. Having switched the cable to 'DL' and connected the radio, the update package still doesn't show any available USB port. Reading online, I came across some instructions for another PD series radio saying that it has to be put into update mode...

Hi Everyone, I dont have much experience with programming so please be patient. I have a new Unication Alpha Elite Secure that will be used for personal paging as well as emergency response. I have the programming cradle and all of the associated cables, etc. I downloaded the PPS software and...

Hey guys, I have been an old conventional scanner listener for a while now. I am switching to a BCD325P2 to finally listen to my counties (Greene County, NC, USA) VIPER fire dispatch and operations channels. That is all I want to listen to. Our county is on the NC VIPER system. I am having...

I just purchased an old bearcat scanner (3&4) that uses crystals, I know these scanners are about obsolete now but, would still love to listen to what I can on this old dog, I joined the fire service in 1978 and that was the first scanner I had bought and have loved this type of scanner ever...

I have been a member of RadioReference and an BCD996P2 owner for almost 3 years and this is my first forum post. I have been trying to program my scanner to always start on my county sheriffs frequency, and that part is easy, but the problem is that the scanner reads the tower sites in...

Hi guys! This is my first message on this forum. tl;dr I don't know how to program these radios and I don't know how to know how to program these radios, but would like to! Also, it seems I don't know what I don't know and request further guidance. I have a lot of EFJ5100 radios with different...

Just got a new SDS200. I made sure both were upgraded to latest software. 1.21.00 for the scanner and 2.03 for Sentinel. I have a good programming cable and get the ka dunk e dunk when i plug it it. Windows 10 says cant find the right driver. So i search here and find a link for Windows serial...

Hi, Our club is operating a hytera rd985 as a 2m repeater. it’s up a hill with no internet connection. What’s the simplest way to connect to it remotely and change setting in the cps? Thanks Angus

Hello all... Just got my SDS100, and it's pretty slick. Of course, there's a learning curve, so I'm here with probably a dumb question about quick keys & scanning. I have three favorite lists each with its own FLQK. Two of the lists are for local police departments with conventional systems...

Good day! Running into a complication. I've mostly been tasked with maintaining the fleet of radios we have, as we often replace radios or expand as our company expands. So we have a few different models, and I have been able to navigate, mimicking the settings just fine. However, they...